RS6-IPRESSPRO BIANCO RAINSAVERMK6 + PUMP CONTROLLER AUTO RESTART 2.2 KW 240V

Code: 804708

Print
Product Code
RS6-IPRESSPRO
RRP: $484.00

Where to Buy

Find Your Nearest Store
Technical Specifications
Product Type Pump Controller
Brand Bianco Rainsaver
Suitable For Clean Water
Bar 9.8 Bar
Amps 16 Amps
Hp 3.0 Hp
Kilo Watts 2.2 kW
Port Size Inlet 1" BSPM Inlet
Port Size Outlet 1" BSPM outlet
Powered Electric
Volts 240 V
Warranty (months) 12 Months
Pack Weight
0.00
Description
RS6-IPRESSPRO

Includes Bianco Rainsaver MK6 & iPress Controller

The BIA-iPRESS is a device used to control electric 240V pumps of 2.2kW or less. The controller monitors both the pressure and the flow and controls the operation of the pump automatically. Because of its design, there is no need for a separate pressure (expansion) tank, nor is there any need to adjust start and stop pressures as per traditional pressure switches.

The unit will protect the pump should the water supply entering the pump is stopped (either due to blockage in the pipe or tank running dry) and will automatically restart normal operation once water is restored.

Controller comes with a fully adjustable cut in (start) pressure of between 0.5-6.0 bar and a cut out (stop) pressure of between 0.8-9.8 bar. The iPRESS has the ability to operate as either a standard auto restart pressure controller (start pressure to be set) or a automatic restart loss of prime pressure switch (start and stop pressure to be set)

The new iPRESS controller combines the advantages of both a standard pressure switch and a typical electronic automatic restart controller

Features and Benefits

  • Starts and stops the pump automatically when the tap is open or closed. This means the operator does not need to turn off the pump after use.
  • Maintains a constant pressure during operation resulting in a reliable water supply when required
  • Automatically stops the pump in the situation of no flow (due to inlet pump blockage) and will automatically resume normal operation once the blockage is removed
  • Automatically restarts normal operation in the event of power being cut off to the control. This gives the homeowner peace of mind that the unit will continue to operate even if they are away on holidays
  • Controller is able to keep the pump running at flows as low as 0.5L/min to maintain water supply
  • Plug and play leads (IEC type) installed on the controller so that a licensed electrician is not required to replace the controller if required
  • Change between Mode 1 (Change Cut In pressure only) and Mode 2 (Change Cut In and cut out) via a single button push.
  • Real time indication of system pressure displayed so a separate in line pressure gauge is not required
  • Special non return valve to avoid water surging.
Technical Specification
Construction Characteristics.
 
Inlet 1” BSP male
Outlet 1” BSP male
Special non-return valve to avoid surges. YES
Security system to avoid operation of the pump without water. YES
Manual start switch (RESET) YES
Voltage LED (POWER) YES
Pump working LED (ON) NO
Security system LED (STATUS) YES
1.5 metre lead and 3 pin Australian/New Zealand plug. YES
0.6 metre pump power lead, 3 pin plug and play YES
 Adjustable cut in (start) pressure YES 
  
Technical characteristics  
Voltage: 220-240V
Maximum current: 16(8) Amps
Maximum kW: 2.2
Frequency: 50 Hz
Ingress protection: IP65
Maximum water temperature: 60 deg C.
Starting pressure 0.5-6.0 bar.
Stop pressure 0.8-9.8 bar.
Maximum working pressure: 10 bar
Minimum flow 0.5 l/m
Downloads
Product Information and Data Sheets
Download Product Information & Data Sheets v1.0
Operation and Installation Manuals
Download Operation & Installation Manuals v1.0
Certificates & Compliance Information
Download Certificates & Compliance Information v1.0
Control Features

Control Features:

  • Proven components
  • Requires no power supply and consumes no electrical energy
  • Designed to operate with pumps and mains up to 1000 kPa (145 psi)
  • Pump flows to 105 l/m, mains flows to 40 l/m (at 500kPa mains)
  • Designed to further save water resources by reducing incoming mains to 200 kPa
  • Requires no weather proofing
  • Can be mounted any distance from the pump underground or inside a tank
  • Completely waterproof - Can be hosed down without the fear of electrocution
  • UV stabilised technopolymer for long life and good looks
  • All Rainsaver MK6 pumps are independently controlled to regulate flows and pressures whilst protecting the pump against voltage fluctuations, loss of water and incorporate a 24 hour automatic pump restart
  • WaterMark approved components for connection to all Town Water supplies. Safe against water borne bacteria, dezincification and lead poisoning
  • No unsightly controller power, water level float cables or the need for a dedicated controller power point
  • Australian owned and designed

Warranty

2 Year Rainsaver MK6 Warranty

Approvals
WaterMark Approved

WATERMARK APPROVAL - ATS 5200.477:2006.

The WaterMark Certification Scheme is a mandatory certification scheme for plumbing and drainage products to ensure that plumbing and drainage materials and products are fit for purpose and appropriately authorised for use in plumbing installations.

The Plumbing Code of Australia requires certain plumbing and drainage materials and products to be certified and authorised for use in a plumbing or drainage installation. These materials and products are to be certified through the WaterMark Certification Scheme and listed on the WaterMark Product Database.

WaterMark Approval Logo

In order to achieve Watermark Certification, the subject material or product must:

  • be tested by a recognised testing laboratory;
  • comply with an approved specification (either a relevant existing standard or an approved WaterMark Technical Specification);
  • be manufactured in accordance with an approved Quality Assurance Program; and
  • carry a warranty.

Materials and products complying fully with the applicable requirements of the WaterMark Certification Scheme are then eligible to be certified by a WaterMark Conformity Assessment Body (WMCAB) and listed on the WaterMark Product Database.

Certified materials and products are identifiable by the WaterMark trademark, which must be displayed on the material or product upon the granting of a WaterMark Certificate of Conformity.

Read more about WaterMark Approvals

Notes

Pressure Systems calculated at 10 L/m

RAINSAVER MK6 - Not for sale seperately
* Warranty Service is provided at the nearest authorised service agent

You may also need these:

WHI-PROMOPUMPCOVER - PUMP COVER BEIGE WHI-PROMOPUMPCOVER 710821